Grizzly G0517g Manual de usuario

MODEL G0517MILL/DRILLINSTRUCTION MANUALCOPYRIGHT © MAY, 2006 BY GRIZZLY INDUSTRIAL, INC.WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SH

-8-Model G0517 Mill/Drill1. EYE/FACE/HAND PROTECTION. Wear safety glasses or face shield when using this machine. Always keep hands and fin-g

Model G0517 Mill/Drill-9-SECTION 2: CIRCUIT REQUIREMENTSFigure 1. Typical 5-15 plug and receptacle.Serious personal injury could occur if you co

-10-Model G0517 Mill/DrillThe Model G0517 was carefully packed when it left our warehouse. If you discover the machine is damaged after you

Model G0517 Mill/Drill-11-The unpainted surfaces are coated with a waxy oil to protect them from corrosion during ship-ment. Remove this prote

-12-Model G0517 Mill/DrillTo assemble the mill/drill:1. Mount the stand to the floor in your desired location.2. Place the splash tray on top of

Model G0517 Mill/Drill-13-Congratulations, your mill/drill is now assembled. For further information about installing the drill chuck or spindl

-14-Model G0517 Mill/DrillTest RunThe purpose of a test run is to make sure your machine and its safety components are function-ing correctl

Model G0517 Mill/Drill-15-Figure 15. Headstock elevation controls.SECTION 4: OPERATIONSNOTICEIf you have never used this type of machine or equipment

-16-Model G0517 Mill/DrillInstalling/Removing Morse Taper SleevesThe Model G0517 includes an MT#1/#2 sleeve and an MT#2/#3 sleeve. Always D

Model G0517 Mill/Drill-17-Installing/Removing Drawbar ToolingThe Model G0517 includes an M12-1.75 drawbar. Use the drawbar to connect the includ



-18-Model G0517 Mill/DrillFigure 29. Loosening lock knob.Belt positions on the pulleys govern the spindle speed. A chart under the belt cover

Model G0517 Mill/Drill-19-The basic operation when drilling is lining up your drill bit with the intended hole location, clamping the workpiece to

-20-Model G0517 Mill/DrillDrilling SpeedsTwist/Brad Point Drill BitsSoft WoodHard WoodPlasticBrassAluminumMild Steel1/16" – 3/16" 3000 2500

Model G0517 Mill/Drill-21-Milling SpeedClosely follow the proper cutting speed—with a reasonable feed speed—to reduce undue strain on all m

-22-Model G0517 Mill/DrillSECTION 5: ACCESSORIESG2500—20-PC Regular Sanding Drum SetThis kit consists of 5 drums in popular 1⁄2" x 1⁄2", 3⁄4

Model G0517 Mill/Drill-23-G9765—9-PC. Ball End Mill SetFeatures 2 flute ball nose end mills. Includes the following sizes: 1/8", 3/16", 1/4&

-24-Model G0517 Mill/DrillSECTION 6: MAINTENANCEAlways disconnect power to the machine before performing maintenance. Failure to do this may re

Model G0517 Mill/Drill-25-Oil FittingsOil fittings are located on the tops of each handwheel and on each side of the base. Lubricate these fi

-26-Model G0517 Mill/DrillThis section is provided for your convenience—it is not a substitute for the Grizzly Service Department. If you need help tr

Model G0517 Mill/Drill-27-Symptom Possible Cause Possible SolutionMachine vibrates excessively or is unusually noisy.1. Motor fan is rubbing on fan co

Table of ContentsINTRODUCTION ...

-28-Model G0517 Mill/DrillElectrical ComponentsFigure 51. Motor wiring inside junction box.Figure 50. Power switch assembly.

Model G0517 Mill/Drill-29-Stand/Base Parts Breakdown

-30-Model G0517 Mill/DrillREF PART # DESCRIPTION REF PART # DESCRIPTION1 P0517001 BASE 35 PW06M FLAT WASHER 12MM2 P0517002 DOOR 36PN43MACORN NUT M12-1

Model G0517 Mill/Drill-31-Headstock Parts Breakdown

-32-Model G0517 Mill/DrillREF PART # DESCRIPTION REF PART # DESCRIPTION68 P0517068 BODY 104 PSS23M SET SCREW M4-.7 X 1069 P0517069 KNOB M8-1.25 X 25 1

Model G0517 Mill/Drill-33-Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of p

CUT ALONG DOTTED LINEName _____________________________________________________________________________ Street ______________________________________

TAPE ALONG EDGES--PLEASE DO NOT STAPLEFOLD ALONG DOTTED LINEFOLD ALONG DOTTED LINEGRIZZLY INDUSTRIAL, INC.P.O. BOX 2069BELLINGHAM, WA 98227-2069PlaceS

-2-Model G0517 Mill/DrillIf you have any comments regarding this manual, please write to us at the address below:Grizzly Industrial, Inc.C/O Technical

Buy Direct and Save with Grizzly®: Trusted, Proven and a Great Value!-OR-• SECURE ORDERING• ORDERS SHIPPED WITHIN 24 HOURS• E-MAIL RESPONSE WITHIN ONE

Model G0517 Mill/Drill-3-Machine Data SheetThe information contained herein is deemed accurate as of 5/12/2006 and represents our most recent product

-4-Model G0517 Mill/DrillThe information contained herein is deemed accurate as of 5/12/2006 and represents our most recent product specifications.Due

Model G0517 Mill/Drill-5-A. ON/OFF Switch w/Safety KeyB. Belt Tension HandleC. Belt Tension LocksD. Headstock Clamp HandleE. Head Elevation Crank

-6-Model G0517 Mill/Drill4. ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause permanent hearing damage. 5.

Model G0517 Mill/Drill-7-7. ONLY ALLOW TRAINED AND PROP-ERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY. Make sure oper-ation instructions ar