Grizzly 10" x 22" Benchtop Lathe G0602 Manual de usuario Pagina 45
- Pagina / 96
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Model G0602/G0752 (Mfg. Since 11/12)
-43-
3. Open the change gear cover, then loosen the
tensioner lock nut located on the other side of
the gear cover plate and the headstock.
The 33" belt is used on pulleys A and C (see
Figure 56) without the tensioner for 720, 1200,
and 2400 RPM.
Figure 58. Location of tensioner lock nut.
4. Move the tensioner to install the 27
1
⁄2" belt
between pulleys B and C, and in sheave 1,
as shown in Figure 55 on Page 42.
5. Re-tension the belt (refer to "Tensioning
V-Belt" on Page 63), then close the change
gear cover and secure it. The lathe is now set
for a spindle speed of 150 RPM.
Locking Nut
Figure 57. G0602 RPM chart.
RPM
Pulley
Combination
RPM Chart
To set the spindle speed to 150 RPM:
1. DISCONNECT LATHE FROM POWER!
2. Refer to the RPM chart in Figure 57 to deter-
mine the pulley combination you need to
achieve a spindle speed of 150 RPM—it is
BC1.
Follow along with the examples below for setting
the Model G0602 spindle speed to gain a better
understanding of this task.
Figure 56. Positioning belt for high speed.
Tensioner
Not Used
A
C
B
G0752 Configuration Example
The V-belt is positioned on the spindle and motor
pulleys with the tensioner (see Figure 59) to select
between low (100-800 RPM), medium (160-1300
RPM), and high (250–2000 RPM) speed ranges.
Figure 59. Positioning belt for low speed.
Tensioner
L M H
Motor
Pulley
Spindle
Pulley
Bolt
- MODEL G0602/G0752 1
- Table of Contents 3
- INTRODUCTION 5
- Model G0602 Identification 6
- Model G0752 Identification 7
- Controls & 8
- Components 8
- Carriage Tailstock 9
- Change Gears, Pulleys, V-Belt 9
- MODEL G0602, G0752 10
- Model Number G0602 G0752 11
- SECTION 1: SAFETY 12
- Glossary of Terms 15
- SECTION 2: POWER SUPPLY 16
- Extension Cords 17
- SECTION 3: SETUP 18
- Inventory 19
- Site Considerations 21
- Lifting & Placing 22
- Leveling & Mounting 23
- Refer to the Lubrication 24
- Section in this Manual 24
- Oil Type 24
- Spindle Break-In 26
- Recommended 26
- Adjustments 26
- SECTION 4: OPERATIONS 27
- Chuck & Faceplate 28
- Mounting 28
- Installation & 28
- Removal Devices 28
- Chuck Installation 29
- Scroll Chuck 31
- Clamping 31
- 4-Jaw Chuck 32
- Faceplate 33
- Tailstock 34
- Removing Tooling 35
- Offsetting Tailstock 35
- Centerline 36
- Dead Centers 38
- Live Centers 38
- Removing Center from Spindle 39
- Mounting Center in Tailstock 39
- Steady Rest 40
- Follow Rest 41
- Carriage & Slide 41
- Compound Rest 41
- Cutting 42
- Tool Post 42
- Manual Feed 43
- *Recommended 44
- G0752 Configuration Example 45
- Power Feed 46
- Setting Power Feed Rate 47
- Threading 48
- Indicator Table 49
- SECTION 5: ACCESSORIES 51
- SECTION 6: MAINTENANCE 53
- Lubrication 54
- Ball Oilers 55
- Leadscrew & Carriage Rack 56
- Compound Slide 56
- Change Gears 57
- Machine Storage 58
- SECTION 7: SERVICE 59
- Operation 60
- Backlash Adjustment 62
- Gib Adjustment 63
- Half Nut Adjustment 64
- Leadscrew Shear Pin 64
- Replacement 64
- V-Belt Tension & 65
- Replacing V-Belt 66
- Timing Belt Tension 67
- & Replacement 67
- Deflection 67
- SECTION 8: WIRING 68
- READ ELECTRICAL SAFETY 69
- ON PAGE 66! 69
- G0602 Electrical Components 70
- G0752 Wiring Box Diagram 71
- G0752 Wiring Box Components 72
- Control Panel 73
- G0752 Motor Wiring Diagram 75
- SECTION 9: PARTS 76
- Tool Post & Compound Rest 79
- Bed & Leadscrew 81
- Steady Rest & Follow Rest 82
- G0602 Motor & Electrical 83
- G0752 Motor & Electrical 84
- Gearbox Parts List 87
- Cross Slide & Carriage 88
- G0602 Labels & Cosmetic 89
- WITHOUT WRITTEN APPROVAL! 90
- SECTION 10: APPENDIX 91
- G0752 Charts 92
- WARRANTY CARD 93
- FOLD ALONG DOTTED LINE 94
- WARRANTY AND RETURNS 95
Relacionado con productos y manuales para Herramientas Grizzly 10" x 22" Benchtop Lathe G0602
Herramientas Grizzly G9979 Manual de usuario
(3 paginas)
(3 paginas)
Herramientas Grizzly G0491 Manual de usuario
(2 paginas)
(2 paginas)
Herramientas Grizzly H0613 Manual de usuario
(2 paginas)
(2 paginas)
Herramientas Grizzly G0538 Manual de usuario
(28 paginas)
(28 paginas)
Herramientas Grizzly H5627 Manual de usuario
(20 paginas)
(20 paginas)
Herramientas Grizzly G0477 Manual de usuario
(48 paginas)
(48 paginas)
Herramientas Grizzly h8234 Manual de usuario
(20 paginas)
(20 paginas)
Atlona AT-VGA0505 manuály
Uživatelské manuály a uživatelské příručky pro Směrovače Atlona AT-VGA0505.
Poskytujeme 1 manuály pdf Atlona AT-VGA0505 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comentarios a estos manuales